![delta unisaw motor delta unisaw motor](https://i.ebayimg.com/images/g/8VYAAOSw7Q1ftDWV/s-l300.jpg)
I'd be happy to answer any questions about it, so feel free to contact me. This is a fairly rare machine in beautiful condition, completely dialed in and ready to use, and with a few modifications that make it even more fun to use than new. It will also come with a large crosscutting sled. I don't have any original inserts for this saw, but it will some with a zero clearance insert I made. The cabinet was also cut for a 3" dust port at some point, and has a few small holes where a slanted floor was installed to trap dust. The fence has a working micro-adjust knob, and the Achilles heel rear clamp is intact. The motor is a 1hp Leeson wired for 110v single phase. New arbor bearings, switch box, all of the standard fasteners were replaced with new stainless steel, and it has a new motor rated switch, wiring, and reproduction switch plate. The cabinet was welded along all of the weak original seams. This saw was completely rebuilt and repainted before I purchased earlier this year (Some of the internals were left with the original paint but cleaned up.).
![delta unisaw motor delta unisaw motor](https://cdnassets.hw.net/dims4/GG/732e3a9/2147483647/resize/480x>/quality/90/?url=https%3A%2F%2Fcdnassets.hw.net%2F11%2F30%2F11c0b9674bdd810db22b908cc5b3%2Ftmp1ad0-2etmp-tcm80-1629568.jpg)
(These are pretty rare!) You can look through the restoration process here:
Delta unisaw motor serial number#
It's serial number 84-8562, and the 76th documented junior. You get what you pay for.I have for sale a fully restored Delta Junior Unisaw. He returned it and bought the Delta motor, and has been happy since. One person who had bought an aftermarket motor had so much trouble with a rumble his motor was making, that he finally tracked down the engineer of the company, who admitted that their motor rotors were originally balanced for 1725 rpm, but they were running them at 3450! They just welded on the special bracket, cut off the old one, substituted a 3450 rpm stator and sent them out the door. I have heard complaints from people who have bought these motors and complained they do not run smoothly. I know there are other "clones" out there, but some of them are of questionable quality. Note: if you have one of the older cabinets with the oval cut-out, you may have to cut out the opening square to allow for the new motor. With a rewind, you get all new wire, with the newer types of high temperature insulation. If you decide to rewind, make sure you go to a quality shop that has rewound these motors before. The older motors had resets built into the motor,or in some cases, did without, and could use simpler switches. You MUST have overload protection installed. The new motors are not overload protected, they rely on overload protection from the switch assembly.
Delta unisaw motor install#
Depending on the switch installed, you may have to install the new GPE style switch. If you want to change out this motor, you will need the new 3450 RPM motor, a new motor pulley ( it’s smaller) and a new set of belts(they are shorter). I see a lot of these motors still in use in old lumber yards. This is plenty of power for the home woodworking shop. The oversize, five and one half inch motor pulley overdrives the arbor to a speed of 3000 RPM or so. Even though these motors were rated at only one to one and one half horsepower or so, they developed a LOT of torque. If you have this motor, and are changing it because it is fried, I would seriously consider re-winding it. Earlier unisaws used a large, one or one and one-half horsepower motor running at 1500 to 1725 RPM. Luckily for me, my unisaw works fine with the motor that is in it- but I found this on the web, thought it was interesting. I'd appreciate any size and brand recommendations, as well as any cautions. I really like the one-button convenience (no RPC to turn on), power-loss safety feature, and overload protection the VFD would provide. Also, would the braking feature of the VFD harm the motor? I see limited application of variable speed, but it would be fun to play with, to a point. I'm hopeful that a run-of-the-mill VFD at the bottom of the price spectrum will do the job.
![delta unisaw motor delta unisaw motor](https://machinerymax.com/Content/listingImages/20191119/9dc716fd-6abe-4542-b005-e8f269e07aec_largesize.jpg)
That seems to indicate that I should be alright, but I want to make sure. My main concern is longevity of the motor. Retrofitting a modern or standard motor requires either butchering the saw's cabinet or modifying the motor and mounting bracket. (They were known as "bullet" motors for their shape.) A single phase bullet motor was available but command a premium on the used market. The motor was purpose built by Marathon Electric just for these saws. I've come into an old (early '60's) Delta Unisaw very cheap.